Step-By-Step Installation Tutorial for the Blue Ox Tail Light Wiring Kit on a 2009 Dodge Ram Pickup

Web Reference: We would like to show you a description here but the site won’t allow us. Sep 26, 2020 · No, I probably didn't take into consideration the fact y'all were 0-10 last year (though it's been mentioned plenty of times in discussion here) and that this is a big step in the right direction for y'all. Jan 16, 2019 · Next year? They are losing like 28 seniors. They will probably take a step back in football next season. West Rusk is returning 1st team DB, 1st team DE, 1st team OL, 1st team OLB, and 2 starting OL, 1 starting receiver, and starting rb. On defense 1 DB returning, OLB’s returning a few d lineman returning On 1/17/2019 at 10:17 AM ...

YouTube Excerpt: Click for more info and reviews of this Blue Ox Flat Tow Wiring Harness: https://www.etrailer.com/Flat-Tow-Wiring-Harness/Blue-Ox/BX8869.html Check out some similar Flat Tow Wiring Harness options: https://www.etrailer.com/dept-pg-Flat_Tow_Wiring_Harness-pt-Bulb_and_Socket_Kit.aspx Search for other popular Dodge Ram Pickup parts and accessories: https://www.etrailer.com/vehicle/2009/Dodge/Ram+Pickup https://www.etrailer.com Don’t forget to subscribe! https://www.youtube.com/user/etrailertv Full transcript: https://www.etrailer.com/tv-install-towbar-wiring-2009-dodge-ram-1500-bx8869.aspx All right, today on this 2009 Dodge Ram pick-up 1500 series quad cab, we're going to install part number BX8869. This is a Blue Ox taillight wiring kit bulb and socket. To start off our install, we're going to take our wire harness with the four wires and we're going to run it through the front of the truck going towards the back. Now our truck has a six volt connector that is previously installed on this truck. This was installed as a part as a base plate installation kit. So I'm going to go ahead and take it back apart and then go ahead and run our wiring through. Now before we install a six volt connector, we'll go ahead and take the rubber cover that comes with it and slide it on our wires first. Once we're all done, we'll go ahead and slide it on the back. We only have four wires to deal with. We'll strip the wires back, twist the copper wire. Now we'll go ahead and make the wire connections to the back of the six volt connector. Our white wire will go to the pin labeled GD for ground, our brown wire will go to the pin labeled TM for running lights, and the green wire will go to the pin named RT for right turn. Our yellow wire will go to the pin named LT for left turn. Okay will all our connections made, we'll go ahead and take our rubber cover and slide it back on to the six volt. Then we'll use some electrical tape to go ahead and seat up the back end up it, and then we'll go ahead and take our six volt connector and mount it back up using the hardware that came with the base plate kit. Now once our connector is secured, we can go ahead and continue on running our wiring towards the back of the truck. Now in this case we're going to run our wires on the inside of the frame. To help us do that, we're using a piece of old airline tubing. Now this could also be a 01:35 inaudible or another stiff piece of wire that could do the job. Basically we're 01:39 inaudible running through a hole in the side of the frame, or in the bottom to the front, tape the wires to it and go ahead and pull it through. We'll go ahead and pull it out through a series of holes in and out threading it through the frame of the truck until it reaches the back end and we'll come out by the bumper. Now we'll go ahead and we'll pull the wire through and take up all our slack. We'll leave it alone for now. Next we'll go ahead and we'll open up the tailgate and then we'll go ahead and remove the taillights. There are two screws on the inside edge of the taillight that we have to remove. Okay, once the taillights are loosened, we'll go ahead and remove the wiring from the taillight as well. We'll go ahead and twist the bulbs out and everything. Now I just have a bare taillight. Now we'll go ahead and find a location for our socket. We're going to use the inside edge of the taillight that goes towards the center of the truck. Once we have our location, you want to make sure you have plenty of room around it because we want to drill a one inch hole, and also we want to make sure we're far enough from the other bulb. Well you want to maintain a distance of at least one inch. We'll drill out a pilot hole first, then we'll go ahead and drill out a one inch hole with our hole saw. Now we'll get our socket ready. We'll go ahead and take the bulb and put it into the socket. We'll line up the pins, push it down, and twist it. Now we can go ahead and install it into the taillight. We'll go ahead and push it into place. Now if this stays loose, the pins that are around the socket can be spread out a little bit to make it fit tighter. So once we have it seated in place, we'll go ahead and take some silicone and seal around the edges. We're done with our driver's side. We'll go ahead and repeat the same process over on our passenger side. Once we have both sides done, we can go ahead and start hooking up wires. We'll go ahead and take our four pull wire, push it up from the bottom, and then out the hole of the taillight assembly. Now we need to strip our wires back. First off, we'll take our green wire, peel it all the way back and run it down the same hole it came out of because eventually this will be ran to the passenger side. Next we'll take our yellow wire and peel it back as well. We'll peel it back and then cut off our excess. It's always a good idea to make sure and leave enough wire that we can

Click for more info and reviews of this Blue Ox Flat Tow Wiring...

Read Full Article 🔍

Curious about Step-By-Step Installation Tutorial For The Blue Ox Tail Light Wiring Kit On A 2009 Dodge Ram Pickup's Net Worth? Explore detailed estimates, income sources, and financial insights that reveal the full picture of their profile.

Source ID: Ax1bGORVG64.

Category: color style guide